Fire Alarm Monitoring for Commercial Buildings in Illinois
A fire alarm that only rings inside an empty building doesn't help anyone. Our UL-listed central station watches your fire alarm 24/7 and sends the fire department the moment it activates, nights, weekends, and holidays included.
Since 1982
40+ years protecting Illinois properties
UL listed
Alarm provider and central station
Bosch authorized
Security dealer
24/7 monitoring
Live operators, every night of the year
What fire alarm monitoring actually has to do
Fire alarm monitoring has to make sure every alarm, every closed valve, and every system fault reaches a person who acts on it.
Not just fires. Everything.
Most people think monitoring is only about fire alarms. But the signals that quietly warn you, like a dead battery, a cut phone line, or a closed sprinkler valve, matter just as much. If those go unnoticed, your system might not work when a real fire starts. We watch all three signal types and respond to each one the right way.
Who we monitor fire alarms for
- Restaurants and retail stores closed overnight and on holidays
- Office and apartment buildings required to monitor by code
- Warehouses and manufacturers with large unattended areas
- Schools, churches, and daycares with fire alarm systems
- Owners whose insurer requires central station monitoring
Monitoring a sprinkler system too? See our sprinkler monitoring and fire alarm inspection and testing pages.
What our fire alarm monitoring covers
Every signal your fire alarm sends gets a specific response from a trained operator.
Fire alarm signals
Smoke, heat, pull station, and waterflow alarms trigger an immediate fire department dispatch.
Response: dispatch fire department
Supervisory signals
Closed sprinkler valves, low air pressure, and similar conditions that need attention soon.
Response: call your contacts
Trouble signals
Battery, power, wiring, and communication faults that could stop your system from working.
Response: call your contacts and service
Dual-path communicators
Send signals over cellular and internet, so one failed line doesn't cut off your monitoring.
Best for: every monitored fire alarm
UL-listed central station
Our station is UL listed and staffed around the clock by trained operators.
Best for: code and insurance requirements
Monitoring certificates
Documentation of your monitoring for your fire department, insurer, or landlord.
Best for: inspections and policy renewals
What happens when a fire starts after closing
Here's how a typical overnight fire plays out at a restaurant with ASI fire alarm monitoring.
Smoke builds in the kitchen
The restaurant closed two hours ago. A smoke detector near the kitchen goes into alarm.
Signal reaches our station
The panel sends the alarm over cellular and internet, with the address and the device that tripped.
Fire department dispatched
Our operator dispatches the fire department right away. Fire alarms are never held for verification.
Owner and key holder called
We call your contacts so someone can meet the fire department and give access.
Event report ready
You get a full record of the alarm, dispatch time, and calls for your insurer and fire marshal.
Local alarm, phone-line monitoring, or dual-path?
How your fire alarm reports matters as much as whether it's monitored at all.
| Setup | Best for | Pros | Trade-offs |
|---|---|---|---|
| Local alarm only | Buildings always occupied, if code allows | No monthly cost | Nobody is called when the building is empty |
| Phone-line monitoring | Older panels still on copper lines | Works with legacy equipment | Phone lines are being phased out |
| Dual-path cellular and IP | Almost every commercial building | Two paths, hard to cut off | May need a communicator upgrade |

Your phone line may not be there much longer
Many older fire alarms still send signals over copper phone lines, and carriers are retiring them. When the line goes, so does your monitoring. Here's how we keep your signals reaching us.
- Communicator upgrades: swap phone-line dialers for cellular
- Dual-path backup: cellular and internet working together
- Daily test signals: we know right away if a site goes quiet
- Trouble follow-up: we call until a fault is handled
- Code guidance: we confirm what your fire department requires
How setup works
Most fire alarm panels can be connected to our station in a single visit.
1
System review
We check your panel, communicator, and current monitoring to see what's needed.
2
Written proposal
You get a monitoring plan and any upgrade costs, with a fixed price.
3
Connect and test
We connect your panel to our station and test alarm, supervisory, and trouble signals.
4
Ongoing support
We send your monitoring certificate and handle service and testing as needed.
Fire alarm monitoring FAQs
Is fire alarm monitoring required for my building?
Many commercial buildings are required to have monitored fire alarms by local code or by their insurer. Your fire department sets the rules for your building, and we'll help you confirm what applies.
What's the difference between alarm, supervisory, and trouble signals?
An alarm means a possible fire, and the fire department is sent. Supervisory means something needs attention, like a closed valve. Trouble means a fault, like a dead battery or lost power.
Do you verify fire alarms before sending the fire department?
No. Fire alarm signals are dispatched right away. Verification is used for burglar alarms, not fire.
Can you monitor a fire alarm someone else installed?
Yes. We monitor most major fire alarm brands and can often switch your monitoring over without replacing the panel.
My panel uses a phone line. Is that a problem?
It can be. Copper phone lines are being retired, and some VoIP lines don't carry alarm signals reliably. We can add a cellular communicator to keep your monitoring working.
Will I get a certificate for my fire marshal or insurer?
Yes. We provide documentation showing your fire alarm is monitored by our central station.
